A big part of decorating your patio is planning the curtains. It's a simple and effortless way to add both style and comfort to a specific area. It's a great way to keep your porch cool and comfortable overall.
And at the same time, these are going to play the main role of a little color enhancer for your outdoor arena. Curtains are also quite good at keeping road noises a little less distracting by softening them. So that's a great way to add style, privacy and calm.
Let's talk about how to hang outdoor curtains with yarn using a very simple process.
Here's how to hang outdoor curtains with yarn.
From beginning to end.
Buying extra rods for outdoor curtains may seem a little unnecessary. In this case, you can very well opt for a wire instead. However, these wires must be strong enough to support the weight of your curtains .Also, we'll start with a few more questions and then continue into the actual installation process.Keep reading…
1.Be careful what thread you use
Wires for hanging curtains outdoors are definitely an affordable route. But be sure to look for a quality wire for your outdoor curtains. Or after just a few days of installation, it may end up on the ground without surprise.
You can choose wrought iron, brass, copper, aluminum or stainless steel wire. Aircraft wire is a good choice as it will still be strong enough to handle these curtains.
2. Take these materials
A.Good quality aircraft cable.B.Curtain hooks or rings.C.Wire cutter.D.Wire rope clips.E.Bit for drilling or piloting.F.Measuring tape.G.Stud Finder.H.Screwdriver, I.Adjustable Wrench.J.Screw Hooks.
3.Height marking on stud location.
For this step you will need a stud finder. Simply use it to locate the studs on both walls, which will have the curtain in between. On each stud you need to mark the two edges. Use a pencil or a marker to make a visible mark. Now you need to measure the height at which you want to hang the curtain. You can do this from the ceiling or even from the floor. Simply use the same marker to mark your preferred height on the stud locations .
4.Added screw hooks.
At the height mark, you need to create pilot holes at this point. Make sure the holes are in the center of each stud. Next, drive the screw hooks into the holes. The screw hooks should hold the wire that will carry the curtains. Be sure to use sturdy screw hooks for this reason, which will be able to support the weight of the curtain. Opt for screw hooks that come with coarse threads. similar to a lag bolt.
Once you start screwing them in, use an adjustable wrench as a lever to push it in properly. You can also use pliers with a large tongue and groove to drive better.
5.Cut the thread to the right size.
Next you will need to get the distance measurements between the two hooks you just attached to the uprights. Now add about another twelve inches to this figure. After that you need to cut the aircraft cable to this dimension. You can just use a wire cutter for the cutting process.
At one end of the cable you need to loop and create a tail 7 inches long. To secure the loops you will need at least two or more than these cable clips. Be sure to loop them tightly with the clips .You need to use a screwdriver or adjustable wrench to tighten these clips.Now bring one looped end to the wall hook you installed earlier.Just hang it on the hook.
6.On the next wall hook.
You need to loosen the turnbuckle now. This will make the wire ends fully extended. On the remaining wall hook, simply place one end of the turnbuckle. Through the free end of the turnbuckle, you then need to thread the free end of the cable. cable must then be pulled. And then simply secure it with the cable clips as before.
Use the wire cutter to cut off any remaining excess cable. To make the cable have your preferred tension, simply tighten the tensioner gradually. Finally, you can put rings or hooks to hang the curtain. In case the curtain sags during suspension, simply tighten the tensioner until you get satisfactory results.
Keep in mind:
This is the title of the box
If you are using very heavy curtains, be sure to avoid using anchor bolts instead of hooks in wall studs. These are not good for heavy curtains covering a large area. vinyl are good for avoiding any kind of fading issue later on.
Conclude
And it was a simple method to hang outdoor curtains with yarn. You can follow the step by step instructions carefully to get a good result. Also, anyone can try this because the process is actually very easy. to do. Those who have never tried home improvement projects can also do very well with this simple chore.
